336-543-5009 hpplumber@gmail.com

Water Heater Repair Greensboro NC's Blog

Greensboro Homeowner advice and maintenance tips for water heaters.

About Greensboro Tankless Water Heaters

For when you need a substitute water heater for your Greensboro office or home, a tankless water heater may be a possible choice. Many individuals still think of them as an actually new item in hot water heating and are unsure concerning just how they operate, exactly what the expense for them is, and just what kind of maintenance they will certainly need. These are a few of the topics we will certainly go over concerning tankless heating units in this article. As compared to conventional tank heaters, as a whole they are 8 to 34 percent a lot more power efficient, give an endless supply of hot water, can run two times the life-span, and need just about one-fifth of the room as other heating units. Let us initially look at just how tankless water heaters work.

Exactly How Tankless Hot Water Heaters OperateTankless Water Heater Installation Greensboro NC

Tankless hot water heater are also knows as on demand water heaters. This is really ideal for they just heat water as it is required … on demand. The traditional picture many people have of the big tank hot water heater in the basement or garage, is constantly heating fresh or the very same water inside its storage tank all day. It must make good sense that this is much more effective than utilizing power to have water warmed. Think about it like keeping a pot of water warmed on ones range all the time to be all set for when one wants a hot cup of tea.

In basic terms, below are the actions involved. The resident turns on a hot water tap in the house. Cold water after that travels down a pipe and into the tankless hot water heater. An electrical element or gas burner (relying on the energy source for the tankless heater) turns on when it knows warm water is desired. The heating element is powerful enough to heat the water instantly as it travels through, after that on its way to the hot water faucet.

Efficiency and Flow Rate

The average flow rate is to be able to give two to five gallons of hot water per min. Gas burning tankless units generally have a greater flow rate compared to electric devices. Nevertheless, gas heaters should have an IID, or intermittent ignition device, set up. Exactly what this gadget does is only allow the pilot light to switch on when water is needed. Water heaters without it might lose energy for the pilot light can be constantly on. If the idea of using a tankless hot water heater is to save money on energy consumption, then it only makes sense to have the most power efficient design possible.

It is this limited flow rate that is most likely the largest disadvantage to a tankless version. A large model may not have the ability to supply the quanity of hot water required if let’s say a dish washer and shower were being used at the same time. One option is to be conscious of what hot water utilizing tools are being used at the same time. That is not also difficult to do.

Another way to get rid of the restricted flow rate is by setting up greater than one tankless water heater in the home. Since they are so little and compact, property owners could set up devoted tankless devices right where they might be required, such as in the kitchen, in the laundry room or near specific bathrooms. This will alleviate the flow rate constraint very quickly.

If one does not wish to initially utilize a tankless style in the entire residence – let us to claim that there is no reason to upgrade the existing hot water heater yet. Or, if a jacuzzi is added, or a brand-new addition to the house is developed the existing traditional water is not large enough to supply the required warm water anywhere, a tankless design can be used an extra heater for merely one or a few areas. It could additionally be good at supplementing a solar water heater as well.

Currently let us look at energy efficiency of a tankless water heater. Homes that utilize less than 41 gallons of hot water a day could possibly provide a 24 to 34 percent rise in water heating efficiency with a tankless design. For those that use a bunch of water, around 86 gallons of hot water each day, could still get 8 to 14 percent energy financial savings. Though this is a larger hot water heater installation cost, yet as much as 50 percent power financial savings are possible with multiple tankless devices near certain hot water outlets.  (http://energy.gov/energysaver/tankless-or-demand-type-water-heaters)

Tankless Water Heater Setup and Maintenance

Greensboro Tankless water heater installations are a bit more intricate than a conventional water heater. It seems every person knows a close friend or has a loved one who could set up a hot water heater. Certainly that may conserve a home owner a little money, however by having an unlicensed individual do it, it could nullify the service warranty. A skilled expert is required for the installment to ensure it functions effectively and offers the performance one is seeking. There are environment, safety aspects, local building code needs that have to be considered.

Similar to any type of water heater, executing upkeep is necessary to do in order to expand the life of the heater and to keep it running at peak effectiveness. The owner’s guidebook will certainly have maintenance recommendations. The main one is to clean the interior with vinegar and flushing out the system.

With having us correctly set up and assist to keep your brand-new tankless hot water heater, it could effortlessly last two decade or longer. That alone is a lot longer time compared to a typical water heater. Certainly we are here to assist with any type of tankless water heater repair in Greensboro NC that may be required likewise.

Stopping the Cause of Water Heater Leaks

A leaking water heater might or might definitely not seem to be a substantial issue. However, it is not important whether it is a significant leak or a tiny leak, either one can lead to a whole lot of destruction for ones household in the form of water problems. Often house owners fail to understand that a tiny leak is typically the indicator of something more substantial that could be beginning to take place, or may happen in the near future. In the worse predicament, that small leak could possibly become a substantial deluge if the water heater is near totally giving out. In any case, we are right here for helping with any kind of Greensboro Hot Water Heater Repair that may be necessary.

Along with water damage to ones property via a leaking storage tank, one can have health associated issues with just about any water leak in a house. The wetness can cause mold or mildew development. People who have problems with allergies or asthma, this isn’t a pleasurable scenario. The EPA says that some mold spores are toxic and can lead to significant health concerns.

Fix any leaks in your home’s roof, walls, or plumbing so mold does not have moisture to grow.  http://www.cdc.gov/mold/dampness_facts.htm

Hoping that a current water leak will correct itself and simply just disappear is something that just doesn’t happen sad to say. Plumbing leaks simply worsen with time. We have written a step-by-step list of actions to do in these situations.

Action Steps for Leaking Water HeatersLeaking Greensboro Water Heater

1. Initially be sure that its the water heater that the leaking water is coming from.

Should there be water near where the hot water heater is situated, the leak may well not always be originating from it. Check out any water pipes or various other objects close to where the heater is located. Does one have any other home appliances close that might form moisture build-up? If ones heater is located inside a basement, this can be the case. It could possibly be a furnace drain line also, or from a water softener.

Initially, clean up the water and see if it comes back any time in the near future by watching the place periodically. Examine the water heater fully to verify if any water is from some of the fittings, T&P valve, or drain valve. When it is entirely dry, continue to look at other things and places close by.

When nothing else is damp in the general space, put paper towels on the floor in the area that was already wet. Take a look at it every hour roughly to make sure the paper towels are still dry. It will likely be a lot easier to notice the paper towels getting wet then the floor. After a day if nothing at all is wet once again, there should be nothing at all to concern yourself with, yet still keep a watch on it the next few days. In cases where water is returning, and there is no other supply in close proximity that it might be from, we will continue to the step two right here to establish the source of the leak.

2. Switch the water heater’s power offBreaker Box for Greensboro Water Heater

Preferably, it is common knowledge that water and electric do not go well together, so shut off the power for safety explanations.

For gas water heaters, there ought to be an on/off dial that must be established to the off placement. Keep the gas line on at this time still.

For electric heaters, head over to the property’s breaker box and turn off the breaker to the water heater.

3. Switch the water supply off

If one is confident that the leak is originating from the hot water heater, and in the event that it is reasonably sizable, turning the water off will eliminate the chance of water continuing to fill up the storage tank and leak within ones home. Once again, with a big leak via the heater, and if the disconnect valve is unable to be gotten to or if it is actually not working properly, go locate and switch off the main disconnect valve for the whole property. If one continues to be uncertain the leak is from the water heater, one can leave the water supply on for the present time.

Remember to be careful that water originating from the storage tank shall be hot and can certainly burn ones skin. Most heaters are going to be set to a temperature of at least 120° F, which can lead to first degree burns on contact.

4. Find the leak’s position

We really do not call for our Greensboro water heater customers to self diagnose their leaks in advance of phoning us, notably when there is a significant water leak scenario taking place, but if one is able to the quicker we can help. The following is a summary of potential reasons why the leak is occurring.

Leaking Water Connections
Verify to assure the cold water inlet as well as the hot water outlet connections are tight. They’re generally positioned towards the top of the storage tank. Utilize a pipe wrench to check they are tight. It is a simple fix when it is from where the leak is coming.

Leaking T&P Valve
Located on the side of the storage tank is the temperature and pressure relief valve. It will in addition have a drain pipe running down to the floor from it. The valve controls how much pressure that accumulates inside the storage tank. It is going to let water out if it needs to regulate the pressure. This valve may be the cause of the leak and could need replacing in the event that it does not remain shut securely. Look to verify if any water is leaking from the valve. If water is coming from the valve when it is in the sealed position, a new valve shall be required. This is certainly a very important valve of the hot water heater, and one that needs to work correctly. However, switching it is not so difficult and not expensive.

Danny Lipford suggests that:

Pressure relief valves sometime develop a drip when opened for the first time in years. Try opening and closing it a few times to see if it will seat itself. http://www.todayshomeowner.com/repair-leaking-water-heater-pressure-relief/

Initially, examine to find out if there may perhaps be dirt in the valve. Place a bucket beneath the discharge tube and open up the valve by lifting the tab on the valve. The water which is discharged may flush the valve and clear away any kind of dirt that may be in the way.

Additional causes of a T&P valve leak might be high water pressure with the local water system, or from a backflow preventer located close to the water meter.Leaking Water Heater Drain Valve

Leaking Drain Valve
Check out the drain valve in the bottom of the heater. They’re often made from plastic, and because of that, may break in the long run. Ensure that it is closed tight. If the drain valve needs replaced, it is a simple fix.

A drain valve leak may well be brought on by debris inside of the valve. Try this first. Put a pail under the valve and turn the valve to open it. Draining some water probably will get rid of the debris. If perhaps following flushing, it continues to leak, it’ll need to be changed.

When the leak is originating from here and the valve continues to leak due to the fact it requires changed, try attaching a hose to it and have the hose go outside. With some luck, that will eliminate the water leaking in the house.

Leak on the bottom of the tank
Whenever the tank leaks from the bottom, it suggests a significant internal issue. As a result of how the water storage tank is constructed, being wrapped inside insulation and having an external layer, when it is leaking, it is going to not be observable from the exterior. An interior water leak usually is going to be seen in the bottom of the tank. The more aged the storage tank is, the much more likely it is starting to decay and deteriorate. A rusting tank will need to get replaced.

5. Will I need a repair or replacement water heater?

From our working experience, we will execute a repair to correct the leak, far more often then having to replace ones heater. The more quickly we can examine the situation, the more quickly we are able to conduct a repair previous to the damage getting any worse. We do highly advocate that any kind of repairs or replacements be done by a pro and not oneself, to ensure they are done the right way and up to code. Often, manufacturer warranties can be voided whenever a non-licensed person works upon it.

Easy Water Heater Maintenance Tasks

Want to accomplish some water heater maintenance today? It is not going to take very long. . .in fact we were planning on ten minutes. Yep, that is all it will take to perform two maintenance chores that any homeowner can complete. The best aspect is they will help Greensboro NC house owners with the following:Greensboro Water Heater Maintenance Steps

Making certain ones water heater runs as long as possible, saving expenses.
Ensuring that ones water heater functions safely.
Ensuring it works as energy efficiently as possible, likewise conserving expenses.

So with that in mind, let us educate you on how to invest 10 minutes once or two times a year to help prevent any water heater repairs for your Greensboro water heater.

Evaluating the T&P Relief Valve

The purpose of the temperature and pressure relief valve, otherwise known as the T&P Valve, is extremely crucial. It has the necessary job of making sure excessive pressure won’t develop on the inside of the water storage tank, which in turn ensures the water heater won’t explode. The infographic below displays the following techniques in evaluating it. The lever needs to be lifted part way and then release it. It is required to snap back to its shut location swiftly. If it is operating correctly, a little water is usually heard entering into the drain pipe below the valve handle that was previously lifted and the sound of a little pressure discharged maybe observed. One will be needing a new valve in the event that non-e of these things happen during the evaluation.

Accomplishing a Mimi Water Heater Tank Flush

Over time, rust and corrosion will occur in the water tank due to the chemical reactions taking place with the components that are necessary to create heated water. We are not planning to go straight into the complex chemical particulars in this article, but through draining some of the water, it helps reduce the sediment, and provide an opportunity to see simply how much sediment is in the water heater.

To accomplish a mini flush, position a bucket below the drain valve, positioned on the bottom part of the tank, and open the drain valve. Just drain a few gallons of water – a few buckets full. Permit the water to sit in the last bucket for a handful of minutes. Once it settles, examine to find out how much stuff has settled to the bottom part of the container. If there is, if the water heater has actually not been drained for a long time (or ever), it would be best to do a complete flush of the tank to get as much of the sediment out as possible.

Take note of how clean the water appears. When it doesn’t seem overly dirty just performing the mini flush will likely be good. If there is a lot of sediment in the water a complete flush should be accomplished. If you’re sure it hasn’t been drained for years, if ever, it will be recommended to empty all of it.

We will not be going directly into all the techniques here to do this, nevertheless for academic purposes, initially reduce the temperature. Wait at a minimum one hour to enable the water to cool down before draining it. Instead of utilizing the buckets, it really is less difficult to attach a hose to the drain valve and drain the water outdoors.

If one begins to hear weird cracking noises from the water storage tank, its a sign that there may be a large amount of sediment building up on the inside. This also reduces the energy efficiency of the water heater.

Water heaters will run well without having very much maintenance, and some property owners really do not do any kind of maintenance with them. But, to get the three benefits mentioned in the beginning of the post, it is crucial to at a minimum complete these two duties. If you have any queries or feel like you need some help the first time, let us know! We are always here to assist and to help avert an undesirable Greensboro Water Heater Repair.

Check out some more ways to increase the heater’s energy efficiency here too.

Water Heater Repair Greensboro

From Visually.

Ways to Increase Water Heater Effectiveness

With the winter weather at its peak, having a hot bath and washing dishes with hot water can be luxurious! But if one’s water heater is taking a long time to heat the water, daily life can get annoying and the winter time could seem even colder. It’s really important, if there is an obvious change in one’s water heater’s efficiency through the winter season, to have the water heater examined by us. Nevertheless, there are actually several maintenance tasks that any homeowner may take on that might considerably impact the performance of the water heater, and help avoid the need for a Greensboro Water Heater Repair.

Care Tasks to Boost Greensboro Water Heater EfficiencyGreensboro Water Heater Efficiency

The very first thing one should do if experiencing a hot water issue is to check the environment nearby the water heater. If the water heater is located in a basement, in particular an unfinished basement, it might be too cold. It would benefit the hot water heater and, consequently, the water that makes its way into one’s house, to get the area surrounding the water heater well insulated and not drafty. Additionally, the hot water lines that bring the hot water from the water heater to the faucets in the property could be getting cold and cooling down the water on the trip. It’s very simple to place pipe insulation around the water line, and the affect could be huge!

Dip Tube Maintenance

A lot of water heaters have a dip tube, a small tube at the base of the tank which lets cold water in the tank while not cooling down the stored hot water around the top. The dip tube is a plastic material, though, and can break or crack. If the dip tube is broken, cold water may leak into the hot water storage, which will cause the water going into the home to be cooler than expected. Thankfully, it is pretty easy to swap the majority of dip tubes.

Water Heater Blankets

These types of specially designed blankets cover the water heater and keep the temperature of the water steady. One may want to think about a water heater blanket if the water heater is cooler to the touch. If a blanket is utilized, one should flip the temperature setting down a bit as the blanket can heat the water, as much as 10 degrees greater than the temperature its set.

In case these servicing duties were tried and one is still having an issue with the temperature of the water, call us! One of our specialists may have to have a look at the heating element or perhaps the pilot burner. Regardless of the problem, we shall have ones water heater functioning at top efficiency quickly!

Removing Water Heater Odors

If the water coming out of the taps inside the house doesn’t smell good, there is probably an issue with your hot water heater. There are a couple of various reasons for stinky water, yet the main cause is bacteria. If bacteria is getting into the water, a smell is likely to develop. Well water is typically to blame for this happening. However, there are a few steps a Greensboro homeowner might take to prevent bacteria from developing in their water and to eliminate current bacteria and smells.

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more here…

Preventing Water Heater Bacteria Growth

The best way to prevent bacteria from growing and bringing about unpleasant tastes and odors throughout one’s property, is to make sure that the temp is fixed at 140 degrees or greater on one’s hot water heater. In this temp bacteria can’t expand and will be killed. When your water heater temperature is placed any lower than this, bacteria will not only exist but will grow.

Cleaning Out Hot Water Heater BacteriaEliminating Greensboro Water Heater Odors

To eliminate present bacteria and smells, one should use harsh chemicals to destroy it. Chlorine bleach is the most efficient and thorough chemical cleaner to use. In the event that you are making an attempt to decontaminate the water and kill the bacteria utilizing bleach by yourself, you should fully understand the precise technique of to do so. First, the electric or gas going to the water heater must be turned off. Then the cold water supply ought to be switched off. Then, you will need to turn on one of the hot water faucets in the house. This allows air into the tank. Using a garden hose, empty the water out of the water heater and close the drain valve after all the water has been drained. After this, it is time to pour in the bleach. One will need five oz of bleach for every gallon of water the tank holds. Unscrew the flexible cold water hose and pour the bleach into the opening. In cases where the cold water hose is not flexible, it might be a wise decision to get in touch with an expert. Connect the water line once again and fill up the tank with water. It is crucial to shut the hot water faucet in the home the moment all of the air is out of the line. It’s likewise very important to run each of the faucets that use hot water within the property until you can smell the bleach. The bacteria that is in the water heater can also be in pipes and fixtures therefore you will have to wipe out the bacteria in those locations at the same time. Let the bleach water sit in the tank and inside the piping for around 3 hours while not utilizing any hot water. And then one more flush is due. Once the tank is cleared once more, don’t put in additional bleach but fill it up with water and let it remain in the tank and inside the piping for a minimum of thirty minutes. Lastly, drain the tank again and then replenish the tank with water. Allow all the hot water fixtures in the house drain until you can not smell bleach. Either switch the power back on or light the pilot light back up and you will be good to go!

For any concerns about water smell, flushing a water heater, Greensboro water heater repairs, or any other water heater concerns, give us a call!

Things to Check With No Hot Water

There could be times whenever one is not getting any hot water whatsoever yet one is certain the water heater is far from needing to be replaced. Right here are three things which Water Heater Repair Greensboro NC advises checking out first to check if they are the cause. All of the items listed are duties that any homeowner could easily carry out, as well.

Greensboro Homeowner Things to Check When Not Having Any Hot Water from the Water HeaterGreensboro water heater repairs

First of all, check the temperature setting on the water heater thermostat. Generally, ones water heater is in a region of the home where there aren’t many things that will occur, nevertheless it is a possibility that the thermostat was bumped and accidentally lowered. We have smaller kids, and you never know what may happen. If it is set at a temp lower than, say, 100 degrees, it was moved. The standard setting needs to be around 120 degrees.

While one is still at the water heater, look to see if the pilot light remains on. It’s a possibility that it has blown out and should be reignited. If the pilot light is out, the water in the storage tank is not going to continue to be hot for too long. A lot of newer water heaters have a self ignition switch that make it straightforward to relight the water heater. If perhaps ones heater is old and has to be “manually” relit, check out the below video to learn the right way to do this:

Not to sound silly, but think whether it is a possibility that the water storage tank is making an attempt at reheating water. In the event that a lot of hot water using products and appliances have just finished making use of, or are in the process of utilizing hot water, the storage tank might need to catch up to the hot water need. If perhaps this is a thing which goes on often in ones house, the size of the present water heater may not be large enough for ones hot water requirements. We can help ascertain if a bigger storage tank is required. We could also share details about tankless water heaters to determine if one would be a fine choice for the property.

In case one has an electric water heater installed in the house, we recommend checking to see if the breaker got tripped. In case it has been tripped, it will not provide electricity for the water heater. If it has been tripped for quite a while, the water within the storage tank will not be very warm, and that is the issue. If perhaps this is the issue, turn the breaker switch off, after that switch it to the on position. Wait one minute to verify it remains on and does not trip itself again. When it does switch off again, call us to find out the reason it isn’t staying on.

There could be various other causes for why the water heater isn’t producing any hot water that we would need to inspect, and are not items one ought to be testing for, on account of safety factors. While a reasonably safe and upkeep free house appliance, hot water heaters may be harmful and must only be maintained by an experienced plumber.

Water Heater Replacement Signs

It’s no surprise a hot water heater will require replacement sometime in the future in ones Greensboro house, still what are the best ways for one to know when that time is getting nearer? It’s always better to prepare for this expense earlier, for certain. Water Heater Repair Greensboro NC suggests enabling us to come out to carry out a yearly inspection of ones water heating system, to ensure one is getting as much as possible from the heater, and also to trying to avoid an unexpected breakdown. Our annual inspection will allow us to keep an eye on ones heater, too, to help know when its life-span is nearing an end, so it isn’t a shock when it occurs. When, however, one hasn’t had a plumbing repair company examine the heater in quite some time, or ever, the red flags detailed below will be handy for certain.

Old AgeWater Heater Repairs Greensboro

Not to be overly obvious, but eventually the water heater will stop functioning properly because of how old the system is. It is beneficial to find out around how old the heating system is. This might be more difficult if it is in a home one bought and a different hot water heater system has not been bought oneself. One should be able to tell from the manufacturer’s label on the heater, ideally. The older the system gets, the more often one will require repairs, certainly.

The Growth of Moisture

Of course, one will have humidity in the air, in the home, from several of the every day usages of water, like from taking a shower or bath, washing dishes, and laundry, but moisture in the air might also be because of the hot water itself. This is a origin of humidity that ought not exist and it is a cause of concern. As the water heater starts to malfunction, it could start to develop little cracks and fractures in the tank. The natural expansion that comes about when the metal walls of the water heater are heated, may cause water leaks. Leaks may also come about because of connections or fittings becoming loosened. When the water leaks continue to put additional moisture in the air, it could gradually result in mold growth and poor inside quality of air.

Rusty Water

Water that is discolored may have causes apart from the hot water heater, but if it is solely if the hot water, never the cold water, is being used, it is a good likelihood it is coming from inside the water storage tank. In case the interior of the water heater is beginning to rust, it could usually result in leaks gradually too. A full inspection may enable us to determine what we are capable of doing to try to put off the necessity for a new water heater now. Even so, there will come a point in time when it is more sensible for a Greensboro Water Heater replacement, because it will lower expenses on operating the heater.